CAN I SET UP A TUB MYSELF? CONSIDERATIONS AND ALSO STEPS

Can I Set Up a Tub Myself? Considerations And Also Steps

Can I Set Up a Tub Myself? Considerations And Also Steps

Blog Article

Course Detail

Do you find yourself trying to find details about How to Install a Bathtub?


A Step-by-Step Guide to Installing a Bathtub
Setting up a tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is additionally a moderately challenging task. If the old tub is easily obtainable, the project can move easily; if you have to open up a wall surface to remove the old bathtub and also position the new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Ensure you have actually certified yourself for the task and also fit attempting it. Instead of employing a contractor to take over a halfway-completed job, it is much better to take into consideration employing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and also do not need to change the plan of your previous water pipelines.
Your devices and material list need to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted gain access to that is commonly the instance.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing compound.
    Before moving on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
    If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Setting up the Bath tub


    Utilizing both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little factors.
    The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the level reviews level.
    To set up faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other faucet.
    Switch on the water system and also check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
    Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least once as this will settle it right into its final setting.

    Getting ready for the Setup


    To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
    Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last setting.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
    You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    Hopefully you liked our article on How to Install a Bathtub Yourself. Thanks so much for taking a few minutes to browse our piece. Are you aware of somebody who is sincerely interested in the topic? Do not hesitate to promote it. We thank you for reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.




    Schedule A Service


    Report this page